Jump to content


Use this Search Box to Find Appliance Repair Help Now
Need help finding your model number?
365-day return policy on all parts purchased here, even electrical parts that have been installed!


FAQs | Store | Memberships | Repair Videos | Boot Camp | Newsletter | Beer Fund | Contact


Welcome to Appliantology.org, the Web's Premiere Appliance Repair Resource for DIYers!

The world-famous Samurai Appliance Repair Forums


You can post a question and get repair help for FREE! Click here to get started.


Already a member of the Appliantology Academy? Just sign in with your username and password in the upper right-hand corner of the screen.

 


Samurai Appliance Repair Man's Blog



How to open a locked door on a GE front load washer

Posted by Samurai Appliance Repair Man, in Washing Machine Repair 09 August 2011 · 1,487 views

Remove bottom panel # 281
and get ya a mirror and flashlight
so you can see the bottom of the door latch,
Item # 217


Posted Image

The tab on the far left with the hole....pull it down...wallah...ur in

Door Latch Link If Needed


Posted Image





Source: GE front load washer WBVH5200J3WW


How to fix a Maytag MAH9700AWW washer with a 2E error code

Posted by Samurai Appliance Repair Man, in Washing Machine Repair 06 August 2011 · 1,149 views

<<<This washer turns on and immediately displays a "2E" code>>>

**********

Replace the MAIN BOARD ==> Circuit Board




Source: Maytag MAH9700AWW "2E" error code


How to fix a Whirlpool-Kenmore gas range with no gas coming out the cooktop surface burners

Posted by Samurai Appliance Repair Man, in Oven-Range-Stove Repair 05 August 2011 · 1,565 views

The real solution was listed in the tech sheet provided below by RegUS_PatOff

COOKTOP LOCKOUT
FEATURE (SOLENOID)
A normally closed (N.C.) electrical solenoid
is located on the back of the range that will
provide a means of shutting off the gas
supply to the cooktop burners. This 120-volt
solenoid is connected across the L1 and
Neutral sides of the line and controlled by a
relay on the microcomputer board. See
Strip Circuit, page 3.
The solenoid is held open to allow gas to
flow to the cooktop burners. If a customer
wants to “Lockout” the operation of the
cooktop burners, they can hold down the
TOP/TOP LIGHT keypad on the control
panel for 5 seconds.
See Use and Care
Guide.
This will open the relay and disconnect the
electrical supply to the solenoid. Once the
electrical supply is disconnected from the
solenoid, the solenoid will close and stop
gas flow to the cooktop. In the event of a
power outage, the gas supply to the
cooktop burners will be shut off.





Source: Kenmore/whirlpool oven 66575842004


How to replace the thermal fuse in a Maytag Neptune MDG6800AWW dryer

Posted by Samurai Appliance Repair Man, in Dryer Repair 04 August 2011 · 3,897 views

Open the door and remove the 2 phillips screws in the hinges (item 20),
remove the 2 phillips screw on the opposite side where the hinges
would be if the door was reversed (item 35)

Flex the 2 upright pieces of item # 22 and pull forward and remove.

The front bulk head item # 29 is held in place with (2) screws on each side.
You will notice that there are 3 screws on each side but one of them on each
side only hols the bulk head together..doesn't actually attach it to the frame.

Once the screws are remove the screws and brackets item # 27.

Now you can raise the top about 2" and pull the bulk head off.
There will be door switch wires attached...you can either leave them in place
or disconnect from the door switch...just remember their locations.


The thermal fuse is item # 40...It will be attached to item # 43 should read "closed" with your meter
or 0 continuity.


If this is the culprit make sure you clean the bulk head / filter housing
as well as check your venting thuroughly for a clogg or restriction.

Thermal Fuse Link

Posted Image






Posted Image


Posted Image


Source: Maytag Neptune Dryer Model # MDG6800AWW


How to remove the door latch assembly in a Maytag MAH5500BWW Neptune washer

Posted by Samurai Appliance Repair Man, in Washing Machine Repair 04 August 2011 · 1,324 views

Open the door and remove the 4 jamb screws...remove front panel...remove 2 5/16"screws at both top corners and remove brackets...remove 4 screws holding dispenser bezel (cover)...lift lid and behold the door latch assembly ...


Source: MAH5500BWW door latch removal






Like - Plus - Connect - View

Facebook-icon50x50.png google-plus-icon-50x50.png YouTube-icon50x50.png

Find Parts & Diagrams Here

Looking for Appliance Parts? Enter your model number, part number, or even a part description and find it here. 365-day return policy on all parts purchased here, even electrical parts that have been installed!

Search My Blog

Latest Visitors

Random Album Image

Whirlpool Dishwasher Wash Motor Failure Analysis, 4 of 5

38 user(s) viewing

0 members, 37 guests, 0 anonymous users


Google (1)


FAQs | Store | Memberships | Repair Videos | Boot Camp | Newsletter | Beer Fund | Contact


Use the Appliantology Parts Finder to Get What You Need!
Enter a model number, part number, type of appliance, brand, or even a part description.
365-day return policy on all parts purchased here, even electrical parts that have been installed!

Your Sometimes-Lucid Host:
Samurai Appliance Repair Man
"If I can't help you fix your appliance and make you 100% satisfied, I will come to your home and slice open my belly,
spilling my steaming entrails onto your floor."

The Appliance Guru | AppliancePartsResource.com | Samurai's Blog

Real Time Analytics