Jump to content


Learn appliance repair at the Samurai Tech Academy.  Learn more.  Earn more.


Use this Search Box to Find Appliance Repair Help Now
Need help finding your model number?
365-day return policy on all parts purchased here, even electrical parts that have been installed!


FAQs | Store | Memberships | Repair Videos | Academy | Newsletter | Beer Fund | Contact


Welcome to Appliantology.org, the Web's Premiere Appliance Repair Resource!

The world-famous Samurai Appliance Repair Forums


You can post a question and get repair help for FREE! Click here to get started.


Already a member of the Appliantology Academy? Just sign in with your username and password in the upper right-hand corner of the screen.

 


Samurai Appliance Repair Man's Blog



Front load washer detergent quantity and type recommendations

Posted by Samurai Appliance Repair Man, in Washing Machine Repair 11 June 2011 · 519 views

Use only HE (high efficiency) detergent in the amounts specified below:

HE: (2) Tablespoons Per Wash load

HE 2X: (1) Tablespoon

HE 3X: (1) Teaspoon



Source: LG WM2233HW Leaking soap drawer


How to remove the brake rotor on Maytag Atlantis and Admiral washers without having to buy that expensive special tool

Posted by Samurai Appliance Repair Man, in Washing Machine Repair 09 June 2011 · 2,019 views

Is this the one with the sticker that sez......"Do not remove cover, spring under 200 pounds.. etc..",,,,,,,,On the Maytag gearboxes, what you would do is remove one screw and go to the hardware store and get 1/2 the amount of screws in the gearbox ( 12 screws , get 6 ),, screws of the same thread but about 2 inches long......On the gearbox, remove alternating screws , like every other one ( on Maytag there is 6 screws ) install the new long screws all of the way, remove all of the old short screws, Then CAREFULLY remove the long screws about two turns at a time on every screw, working around the cover.....IF the cover is not loose as you are running out of threads, you need longer screws.... Reinstall in the reverse order using the long screws to suck the cover down, install the short, original screws and so on....





Source: Admiral Washer Brake Rotor Romoval LNC6760B71


How to get to the drain pump in a Whirlpool LHW0050PQ4 front load washer

Posted by Samurai Appliance Repair Man, in Washing Machine Repair 08 June 2011 · 1,165 views

You have to change your pump through the back panel. Remove the top first, 2 screws on the back of the top panel then 10 screws on the back panel





Source: WHIRLPOOL LHW0050pq4 Front load washer


How to change the water inlet temperature settings on an Asko 640 washer

Posted by Samurai Appliance Repair Man, in Washing Machine Repair 08 June 2011 · 452 views

To change the water inlet setting, turn the machine on and then press "Enter" 4 times in rapid succession quickly followed by pressing P4 four times in rapid succession and "Inlet Function" appears on the screen and you can change it between H or C.


Things to check on a Samsung WF218ANW/xaa washer that won't fill with water

Posted by Samurai Appliance Repair Man, in Washing Machine Repair 07 June 2011 · 2,496 views

Re-verify that the cold & hot water hoses are connected correctly (hot hose to hot valve & cold hose to cold valve).

Inspect the black tube on the WATER LEVEL SENSOR. It should be attached to the SENSOR and the tiny spring-clamp should be securely holding the tube in place.


Usually a *NO FILL* symptom will trigger an error message.

"nF" : No Fill

"LE" : Water Level Sensor Error

The WATER LEVEL SENSOR should give 22 to 24 OHMS at the *pink* & *violet* connections of the SENSOR (remove plug to test sensor).

If the WATER LEVEL SENSOR is "good"---start a cycle with HOT water selected.

The HOT WATER VALVE should be getting 115/120 volts AC (within 30 seconds).

Turn off the washer---turn on washer.

Repeat the test using a cycle for COLD water only. One of the COLD WATER VALVES should be getting 115/120 volts AC (within 30 seconds).

If not---try clearing the EEPROM...

Power off washer.

Press the following buttons at the *same* time:

DELAY START

SIGNAL

POWER (on).

Test washer functions again to see if water enters.

If not---order a new MAIN BOARD.

NOTE:

There are 2 versions of this washer (with the same model number). Use the SERIAL NUMBER to order the *correct* MAIN BOARD.

NOTE #2

If a new MAIN BOARD has been installed---perform the EEPROM clear/reset procedure *again*. This resets the "computer" (new board).

If this is not done---it can appear that the new board is *defective* as the washer will not function properly (erratic operation).





Source: Samsung WF218ANW/xaa






Like - Plus - Connect - View

Facebook-icon50x50.png google-plus-icon-50x50.png YouTube-icon50x50.png

Find Parts & Diagrams Here

Looking for Appliance Parts? Enter your model number, part number, or even a part description and find it here. 365-day return policy on all parts purchased here, even electrical parts that have been installed!

Search My Blog

Latest Visitors

Random Album Image

Burned Refrigerator Compressor Start Relay

5 user(s) viewing

0 members, 5 guests, 0 anonymous users


FAQs | Store | Memberships | Repair Videos | Academy | Newsletter | Beer Fund | Contact


Use the Appliantology Parts Finder to Get What You Need!
Enter a model number, part number, type of appliance, brand, or even a part description.
365-day return policy on all parts purchased here, even electrical parts that have been installed!

Your Sometimes-Lucid Host:
Samurai Appliance Repair Man
"If I can't help you fix your appliance and make you 100% satisfied, I will come to your home and slice open my belly,
spilling my steaming entrails onto your floor."


The Appliance Guru | Master Samurai Tech

Real Time Analytics