Jump to content
Click here to check out this guide

FAQs | Repair Videos | Academy | Newsletter | Contact


DISCLOSURE: We may earn a commission when you use one of our coupons/links to make a purchase.
  • Upcoming Events

    • 30 March 2024 02:00 PM Until 03:00 PM
      0  
      All Appliantology tech members are invited to join in this workshop on all things Appliantological: bidness, customers, tools, troubleshooting, flavorite brewski, whatever. Webcams and microphones are open and live!
      This workshop is also a great time for any students at Master Samurai Tech to bring any and all questions about the coursework. We're happy to walk through any concepts you're having trouble with. Think of it like office hours with your teachers. 
      If you have a specific appliance problem you'd like us to talk about, post it here! We need a problem statement and a PDF of the tech sheet or schematic so we can all see it on screen share. If you have a PDF that isn't already in the File library here at Appliantology, send it to us by attaching it to the contact form. 
      Also, follow this Calendar Event so you'll get notified of new posts here. Look for the "Follow" button either at the top of the topic on desktop or below the topic on mobile.
      Who: This workshop is only available to tech members at Appliantology.
      When: Saturday, March 30 @10:00 AM Eastern Time.
      Where: Online via Zoom
      How:
      Click here to go to the forum topic with the registration link. If you're interested, register now. Arrive a couple minutes early to make sure your connection is working. Set a reminder for yourself for this workshop so you don’t miss it.  And check out past workshops here: https://appliantology.org/announcement/33-webinar-recordings-index-page/

Testing the old limit control that the furnace guy said was bad


Lisa

Recommended Posts

 I measure the limit control resistance at room temperature - the multimeter reads very low  (1.8 at the most sensitive setting, a length of wire is 0.3)  so the current should flow and allow the gas valve to open and ignite the burners.

Now I test to see if it failed at turning off the gas in case the temperature had exceeded the upper limit, allowing the thermal fuse to open.  I set the upper limit to 100 deg.  I put it in the oven at 140 deg.  I measure the resistance and the ohmmeter reads "I" (this is I for Infinity, not a number 1, correct?)  So the switch is open, there is no current, and I know the upper limit did not fail.

The old fuse also has a resistance of I.

Is this method correct?  What setting should I use on the ohmmeter - it goes from 200 to 2000K.   It's a 29V circuit, not sure what current it draws.

I'm definitely asking the heating service company for my money back.

The repairmen coming to my house have been batting .400 on diagnosis.  That's great - for baseball.

Link to comment
Share on other sites

  • Replies 9
  • Created
  • Last Reply

You are correct in your testing.:clapping: When the circuit is closed resistance should be at or near 0, when open (sensed temp is greater than setting) circuit is infinity.

Is it possible the "furnace guy" called the thermal fuse a limit or did he specifically point out the fan/limit control? Just wondering where he was headed in his diagnosis since the fan/limit is such a common part and would not require "ordering".

Link to comment
Share on other sites

No, he called it a limit control, held the limit control,  cursed at the limit control while detaching it.

He said "This side (the blower side) is 120V and this side (the valve-igniter side) should be 24V and it's 0."

You know what?  It still is right now, in my working furnace.  The blower side is 120V because that switch is open, and the valve-igniter side is 0V because that switch is closed, waiting for the thermostat to complete the circuit OR for the upper temperature limit to be exceeded, and then the switch opens and the gas valve shuts off.   And when the burners are on and the blower is running, both sides will be 0V.

So he got the numbers and interpreted them wrong - they actually meant that the limit control was working and he should look elsewhere.

He did not pull the sheathing off the fuse, but I did - and the voltage there was 29V meaning that fuse was open and I needed a new fuse.

Link to comment
Share on other sites

Just found where my husband put the receipt - says "Limit cot. is out - they will call if they want us to fix it."

Ha.

Link to comment
Share on other sites

My only question is why did your thermal fuse "blow"? It has a temperature range on it and they only blow for one of two reasons. The area it is mounted on exceeded its designated temperature or it handled excessive amperage and burned out (unlikely but possible).

You need to find out why it "blew".

Link to comment
Share on other sites

I don't know - I didn't observe any flame roll-out while I was watching.

Could it just get old and glitchy?  About 10 days before the fuse shut down for good, the furnace stopped working, and started again for no reason I could figure out after I poked around a while.

The furnace has had no problems at all since I put the new fuse in Thursday.

Link to comment
Share on other sites

[user=20480]birdg[/user] wrote:

Could it just get old and glitchy? 

No, these thermal fuses are a one-shot deal. They don't sporadically fail.

Link to comment
Share on other sites

i belive the correct  term would be (fan/limit) control  is it a (Camstat , or a Honeywell) does it have 4 wires or 3 ?

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.


×
×
  • Create New...