Jump to content
Click here to check out this guide.

FAQs | Repair Videos | Academy | Newsletter | Contact


DISCLOSURE: We may earn a commission when you use one of our coupons/links to make a purchase.
  • Upcoming Events

    • 30 March 2024 02:00 PM Until 03:00 PM
      0  
      All Appliantology tech members are invited to join in this workshop on all things Appliantological: bidness, customers, tools, troubleshooting, flavorite brewski, whatever. Webcams and microphones are open and live!
      This workshop is also a great time for any students at Master Samurai Tech to bring any and all questions about the coursework. We're happy to walk through any concepts you're having trouble with. Think of it like office hours with your teachers. 
      If you have a specific appliance problem you'd like us to talk about, post it here! We need a problem statement and a PDF of the tech sheet or schematic so we can all see it on screen share. If you have a PDF that isn't already in the File library here at Appliantology, send it to us by attaching it to the contact form. 
      Also, follow this Calendar Event so you'll get notified of new posts here. Look for the "Follow" button either at the top of the topic on desktop or below the topic on mobile.
      Who: This workshop is only available to tech members at Appliantology.
      When: Saturday, March 30 @10:00 AM Eastern Time.
      Where: Online via Zoom
      How:
      Click here to go to the forum topic with the registration link. If you're interested, register now. Arrive a couple minutes early to make sure your connection is working. Set a reminder for yourself for this workshop so you don’t miss it.  And check out past workshops here: https://appliantology.org/announcement/33-webinar-recordings-index-page/

Weathermaker 8000


Tsuriman

Recommended Posts

Sorry for the Unsui move of no model number, I will get one asap, will go back in a little while.

Tenants said that heat was intermittent. (Why I cant I get these calls during the week?)

Furnace flashing code 14 - Ignition Lockout - Ignition will auto reset after 3 hours (refer 34)

I open the unit and put back together, tripping the door switch I guess, she started to cycle again.

LED steady. Everything seemed normal, little fan spinning, blower starts up, ignition coil turns read, flames look great.... and poof, everything shuts down. ( Want to say the blower stopped at some point and I wasnt sure if that was normal.)

LED flashing code 34 - Ignition Proving Failure Control will try 3 times...

3rd time a charm. Lights up, fires up, blower running, heat good. Light steady when I left, but I know I need to do something.

Service code 34 says:

-Oxide build up on O2 sensor (clean with fine sandpaper)

-Proper Flame sense microamps (.5 microamps minimum)

-Gas stuff ( I think is fine)

Green wire (ground?) check

Inadequate flame carry over or rough ignition.

Plan to clean O2 sensor (where?), check my ground and replace the filter. Also while every thing is open give the blower and other dusty components a good dusting.

You guys know, what else do I need to do, check, etc.

DOMO arigatou.

Tsuriman

2011-12-10_12-19-55_367.jpg

Link to comment
Share on other sites

  • Replies 2
  • Created
  • Last Reply

Top Posters In This Topic

  • Tsuriman

    2

  • jumptrout

    1

Top Posters In This Topic

Sounds as if the flame sensor is short cycling the unit. Clean the flame sensor rod. If this installation is horizontal probably on the top burner.Unless it is horizontal right output then the lower burner. If vertical on the right burner. If downflow on the left burner.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...