Fisher paykel gwl10u2 washer stops and beeps constantly before rinse cycleFisher paykel Washer Gwl10u2 Beeps Stops before rinse
Posted 13 March 2012 - 08:41 AM
Posted 14 March 2012 - 03:36 PM
What pattern of lights is on the panel while it's beeping ... which lights are steady and which are flashing, if any?
My initial guess is a problem with either the diverter valve or the pump. The diverter controls to where water goes when the pump runs ... either back into the tub through the recirculation port, or out the drain hose. If the diverter is clogged or broken/malfunctioning, then water may recirculate when it supposed to be draining (i.e. at start of the rinse phase). The controller board will detect that the water level in the tub not dropping when it should be draining and trigger an error code. The pump of course must run for the water to drain.
If the machine is 10 years old and has the original pump, you also *need* to look under the machine at the pump for evidence of leaking (rust or mineral deposits on the pump) ... even if you're not seeing water leaking on the floor. A slow leak/drip keeping the pump wet over time can cause it to short-out and kill the controller board. A replacement pump is not so expensive ... compared to a pump + a controller board.
Posted 03 November 2012 - 08:25 AM
Posted 03 November 2012 - 09:40 AM
While carrying out a bowl check, the Motor Control Module has found that the bowl is not engaged
even though the pressure sensor indicates that the bowl is empty.
The Motor Control Module continues to check for 2 minutes.
During this time the module has not been able to determine a valid bowl status and so displays this fault.
This fault differs from fault 40 in that a valid bowl status could not be determined.
The first two areas to check are the clutch and the pressure tube.
If these two appear correct, then the fault could be with the pressure sensor in the Motor Control Module.
Primary Source: Mechanical.
Action: 1. Check that there are no clothes or other foreign objects preventing the clutch from reengaging.
2. Next check that the pressure tube has not come off and that it is not kinked.
Secondary Source: Motor Control Module.
Action: Replace Motor Control Module, if the above checks out without fault.
48. (00110000) Phase 2 to 6 - Hot and Cold Valve Faulty
The Motor Control Module has measured voltages from the valve diagnostic circuit that indicate
both the hot and cold valves are faulty.
The most likely cause is that the valve harnesses have not been connected correctly or the valve is open circuit.
Primary Source: Wiring.
Action: Check the valve harnesses are correctly fastened to the valves or the pins are not bent backwards.
Secondary Source: Water Valves.
Action: Check the valve coils are not faulty (open circuit).
Tertiary Source: Motor Control Module.
Action: Replace the Motor Control Module.
one of my video productions: “Easter Seals: Walk With Me”
every day is Down Syndrome Awareness Day
"A Child Is Waiting" . Burt Lancaster . Judy Garland . 1962
RegUS_PatOff > www.youtube.com/watch?v=oPAY2LsKVEw
Posted 04 November 2012 - 12:26 PM
Posted 04 November 2012 - 01:35 PM
Posted 04 November 2012 - 10:23 PM
DO NOT try to drain the "trapped" water. It's supposed to be in there ... water-filled balance rings at top and bottom. Drilling holes to drain the rings will destroy the basket.
lol, yeh the bowl leaked water inside so i drilled some holes and drained it out
lmao , well that sir is why your machine doesnt work , its supposed to have water in there
havent met one of those guys lately but it must be due again
Also tagged with one or more of these keywords: Fisher paykel, Washer, Gwl10u2, Beeps, Stops before rinse
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users