Hi guys/ I have a duet sport, customers actually, went on a no spin complaint. pulled an f01 code, replaced the ccu as directed. week later, same thing. not throwing codes, walks through diagnostics intermittantly. is there something I'm missing? checked all the usual suspects, pump was recently replaced. Any insight here? I ordered a new mcu but not sure if it will fix. seems a little quirky ramping up in diagnostic mode, sometimes spins sometimes not. cust can get it to spin out after repeated attempts. Any suggestions greatly appreciated. Thanks !
Appliantology Parts Search Box
Enter a model number, part number, type of appliance, brand, or even a part description.
365-day return policy on all parts purchased here, even electrical parts that have been installed!
FAQs | Parts | Memberships | Repair Videos | Newsletter | Beer Fund | Contact
110.46462501 duet sport no spin intermittant
Started by telefunkenu47, Oct 09 2012 03:38 PM
4 replies to this topic
#1
telefunkenu47
-
- Sublime Master of Appliantology
-
- 322 posts
Kohai
Posted 09 October 2012 - 03:38 PM
Even root canal is easy...if you're a dentist...
Use the Appliantology Parts Search Box to Find What You Need!
Enter your model number, part number, type of appliance, brand, or even a part description.
365-day return policy on all parts purchased here, even electrical parts that have been installed!
#2
jumptrout
-
- Academy Fellow
-
- 1,142 posts
Sensei
- Location: USA
- Flavorite Brew:Coors Light
Posted 09 October 2012 - 05:37 PM
I would verify the signal from the door switch.
- Samurai Appliance Repair Man, kdog and tommytech like this
#3
telefunkenu47
-
- Sublime Master of Appliantology
-
- 322 posts
Kohai
Posted 09 October 2012 - 10:59 PM
have you seen this on the sport?
Even root canal is easy...if you're a dentist...
#4
telefunkenu47
-
- Sublime Master of Appliantology
-
- 322 posts
Kohai
Posted 10 October 2012 - 07:49 PM
could the pressure switch be causing the unit to go out on suds? since this washer has no display, there wouldnt be a failure code would there? how would one go about verifying that this is happening?
Even root canal is easy...if you're a dentist...
#5
Samurai Appliance Repair Man
-
- Fermented Grand Master
-
- 24,334 posts
Your Sometimes-Lucid Host
- Location: USA
- Flavorite Brew:Kirin Ichiban
Posted 10 October 2012 - 07:56 PM
A slow drain or clogged/flakey pump will cause this error, too.
If you're sure the pump and drain check out good, then replace the CCU ==> http://www.repaircli...er=110.46462501
HINT: In situations like this where an analytical solution is elusive due to shitty information from the manufacturer, I always buy the expensive control board from RepairClinic so I can return it in case I'm wrong.
If you're sure the pump and drain check out good, then replace the CCU ==> http://www.repaircli...er=110.46462501
HINT: In situations like this where an analytical solution is elusive due to shitty information from the manufacturer, I always buy the expensive control board from RepairClinic so I can return it in case I'm wrong.
- kdog likes this
FAQs | Parts | Memberships | Consultations | Repair Videos | Newsletter | Beer Fund | Contact
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users
FAQs | Parts | Memberships | Repair Videos | Newsletter | Beer Fund | Contact
Use the Appliantology Parts Finder to Get What You Need!
Enter a model number, part number, type of appliance, brand, or even a part description.
365-day return policy on all parts purchased here, even electrical parts that have been installed!
Your Sometimes-Lucid Host:
"If I can't help you fix your appliance and make you 100% satisfied, I will come to your home and slice open my belly,
spilling my steaming entrails onto your floor."
ApplianceGuru.com | AppliancePartsResource.com | Fixitnow.com
