Bad Control Panel?
Any help would be appreciated.
Thanks
Edited by richseattle56, 06 December 2012 - 06:49 PM.
Appliantology Parts Search Box
Enter a model number, part number, type of appliance, brand, or even a part description.
365-day return policy on all parts purchased here, even electrical parts that have been installed!
FAQs | Parts | Memberships | Repair Videos | Newsletter | Beer Fund | Contact
Welcome to Appliantology.org, the Web's Premiere Appliance Repair Resource for DIYers!
We have loads of repair manuals, photos, diagrams, personal instruction, and appliance parts-- everything you need to get it fixed and fixed right away!
You can post a question and get repair help for FREE! Click here to get started.
Already a member of the Appliantology Academy? Just sign in with your username and password in the upper right-hand corner of the screen.
JDB1100AWS Jenn-Air dishwasher does not start.
Started by richseattle56, Dec 06 2012 06:46 PM
5 replies to this topic
#1
richseattle56
-
- Chief Appliantologist
-
- 302 posts
Kohai
- Location: USA
- Flavorite Brew:Coors Light or Vodka
Posted 06 December 2012 - 06:46 PM
On the control panel the only LED that comes on when you press the buttons is the Normal Wash, every now and then you can get the button to the right of Normal Wash to Light up. Press the Normal Wash LED lights, Press Heated Dry no light, Press start no LED, no start. Tech sheet says press the heated dry 6 times and then press Start/Cancel button to enter field test mode. Nothing. Any IDEAS.
Bad Control Panel?
Any help would be appreciated.
Thanks
Bad Control Panel?
Any help would be appreciated.
Thanks
Use the Appliantology Parts Search Box to Find What You Need!
Enter your model number, part number, type of appliance, brand, or even a part description.
365-day return policy on all parts purchased here, even electrical parts that have been installed!
#2
Samurai Appliance Repair Man
-
- Fermented Grand Master
-
- 24,708 posts
Your Sometimes-Lucid Host
- Location: USA
- Flavorite Brew:Kirin Ichiban
Posted 06 December 2012 - 10:42 PM
This is almost always a bad touchpanel ==>
http://www.repaircli...mber=JDB1100AWS
You can check the keypad continuity at the ribbon cable using the matrix in the tech sheet.
PMed you the service manual.
- kdog likes this
FAQs | Parts | Memberships | Consultations | Repair Videos | Newsletter | Beer Fund | Contact
#3
jb8103
-
- Chief Appliantologist
-
- 459 posts
Kohai
- Location: USA
- Flavorite Brew:Ginger ale
Posted 06 December 2012 - 11:13 PM
Been down that road - new keypad didn't work, new circuit board didn't work, could have been a bad motor screwing up the circuit board in the first place. That's where the customer balked. I lost hundreds on that job. We need diagnostic answers for this situation.
First, do no harm.
#4
Samurai Appliance Repair Man
-
- Fermented Grand Master
-
- 24,708 posts
Your Sometimes-Lucid Host
- Location: USA
- Flavorite Brew:Kirin Ichiban
Posted 07 December 2012 - 12:01 AM
If the motor is bad, you can determine this by seeing if its getting 120vac when it should be running.
As mentioned, you can also test the touchpad using the matrix in the tech sheet.
As mentioned, you can also test the touchpad using the matrix in the tech sheet.
FAQs | Parts | Memberships | Consultations | Repair Videos | Newsletter | Beer Fund | Contact
#5
kdog
-
- Academy Fellow
-
- 7,433 posts
RoughShod
- Location: Canada
- Flavorite Brew:Dickens Cider
Posted 07 December 2012 - 12:21 AM
This may seem rather automatic, but we are always checking the power connections ? Including proper polarity/ground etc ?
I have seen a number of issues arise from partial/poor connections
- Samurai Appliance Repair Man likes this
Help us keep the lights on: buy appliance parts here ==> http://repairclinic.com
For service manuals and lots of other goodies, become an Apprentice ==> Apprenticeship
For service manuals and lots of other goodies, become an Apprentice ==> Apprenticeship
#6
richseattle56
-
- Chief Appliantologist
-
- 302 posts
Kohai
- Location: USA
- Flavorite Brew:Coors Light or Vodka
Posted 07 December 2012 - 05:52 PM
Well after reading jb8103's post, needless to say, I was a little worried about replacing the control panel. So I took apart the door and disconnected and reconnected the ribbon strip from the control panel to the control board, no change. Looking closely at the ribbon I notice that the connection points looked all scratched up. So, I went ahead and replaced the control panel. As I was going down to flip the breaker back on, I was praying the problem would be solved. Came back and pressed the Heavy Wash Light came on, pressed Normal Wash Light came on and Heavy went off, pressed Heated Dry, light came on. Pressed start machine started to fill, fell to my knees and thanked God. All is well.
Thanks for all the help.
Edited by richseattle56, 04 March 2013 - 10:41 PM.
- Samurai Appliance Repair Man, kdog and certified tech group 51 like this
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users
FAQs | Parts | Memberships | Repair Videos | Newsletter | Beer Fund | Contact
Use the Appliantology Parts Finder to Get What You Need!
Enter a model number, part number, type of appliance, brand, or even a part description.
365-day return policy on all parts purchased here, even electrical parts that have been installed!
Your Sometimes-Lucid Host:
"If I can't help you fix your appliance and make you 100% satisfied, I will come to your home and slice open my belly,
spilling my steaming entrails onto your floor."
ApplianceGuru.com | AppliancePartsResource.com | Fixitnow.com
