Jump to content

Learn appliance repair at the Samurai Tech Academy.  Learn more.  Earn more.

Parts Search
Site Search

FAQs | Store | Memberships | Repair Videos | Academy | Newsletter | Beer Fund | Contact

Welcome to Appliantology.org, the Web's Premiere Appliance Repair Resource!

The world-famous Samurai Appliance Repair Forums

To get started, click here.

Already a member of the Appliantology Academy? Just sign in with your username and password in the upper right-hand corner of the screen.



Member Since 07 Jun 2006
Offline Last Active Feb 18 2015 01:33 PM

Topics I've Started

GE Built in ref condensation issues and now temp issues ZISB420DMB

07 February 2015 - 04:07 AM

OK THIS time I have a model number. Any of you see this before? I have a GE SxS built in, Model:  ZISB420DMB   Customer has condensation at the upper left rear corner of the refrigerator section. Damper was just replaced. Temps in the freezer are colder than requested, Refrig section is warmer than requested. Temps set at 0*F in Freezer and 36*F in Ref









Top Loader WP WTW5700SW0 water temps erratic

09 October 2014 - 08:10 PM

Hello all again... I am working on my friend's washer (Whirlpool) and it wants to act funny. You set the temp for incoming water and it does what it wants to do. Sometimes, hot is cold,  and sometimes it acts normal. Are we looking at a temp control? What is your experience?


Thanks in advance for your help.





Kitchen Aid dishwasher (KUDE03FTSS1) verrrrrrrry slow drain

02 May 2014 - 11:00 AM

Good morning ladies and gentlemen,


I am once again upon a head scratcher that has me bewildered. (like that word?)


I have a customer with a KA dishwasher that wont drain completely.


What has been done:


1. Drain pump replaced.

2. Drain line snaked out (clear)

3. Air gap checked and cleared

4. Sump area cleared

5. old pump was a 4 "vane" impeller... new one had an 8 "vane" impeller


Still slow ... Is the control board controlling the speed (or lack thereof) to the pump?


Thank you in advance for all your help.

Kenmore 110.88752796 Replaced transmission now spin is STRANGE!

23 April 2014 - 08:13 PM

OK So I have this stack washer (direct drive) that was just grinding, Yellow oil all over the floor and dripping oil. I replaced the transmission, YAYYYYYY!!! Agitate works... go into spin and it is pumping out yet the transmission is not basket is not engaging... HOWEVER (and this is the weird part) when you open the lid and then close it, THEN it spins fine.


Clutch? Basket Drive?


And why would it not engage after shifting into spin yet, opening and closing the lid will engage?

GE SxS GSS25LGMBCC mold in dispenser

26 August 2013 - 07:20 PM

I have a customer who has a 10+ year old GE refrigerator. Previous service company found a solenoid dispenser rusted stuck. Replaced it to the tune of $460.00 (I know... OUCH!.. I almost cried for her) So now there is a bit of condensation and mold up in the area where the dispenser door is. I laser temped the area and the ambient was about 73*F and the dispenser was at 61*F on the left and 55*F on the right of the disp door.


When the previous service company was called back, she was told it was "GE Door Disease" WTH? Never heard of it.


I am begrudgingly thinking we may have saturated insulation causing the mold. What says the hive?


Thank you for your time



Here is the pic of condensation and mold



FAQs | Store | Memberships | Repair Videos | Academy | Newsletter | Beer Fund | Contact

Use the Appliantology Parts Finder to Get What You Need!
Enter a model number, part number, type of appliance, brand, or even a part description.
365-day return policy on all parts purchased here, even electrical parts that have been installed!

Your Sometimes-Lucid Host:
Samurai Appliance Repair Man
"If I can't help you fix your appliance and make you 100% satisfied, I will come to your home and slice open my belly,
spilling my steaming entrails onto your floor."

The Appliance Guru | Master Samurai Tech

Real Time Analytics