Troubleshoot modern appliances with confidence…

Click here to check out our structured, online appliance repair training courses for rookies and experienced techs.

FAQs | Repair Videos | Academy | Newsletter | Podcast | Contact

Stay connected with us...

Samurai on Facebook - become a fan today! Sign up for our free newsletter and keep up with all things Appliantology. Subscribe to our YouTube channel for lots of appliance repair tips and help! Follow the Samurai on Twitter and get timely morsels of Appliantological Wisdom! Subscribe to our MST Radio podcast to learn secrets of the trade.
  • Announcements

    • Samurai Appliance Repair Man

      [Webinar] Basic Refrigeration Sealed System Thermodynamics   09/21/2017

      See this calendar event for details:                   
    • Samurai Appliance Repair Man

      Webinar Recordings Index Page   09/21/2017

      One of the benefits of your Professional Appliantologist membership is that you can attend the regular, live training webinars and you have access to the recordings as well. So if you can't make it to the live webinar, catch the recording at your convenience. The webinar recordings are conveniently listed for you on the Webinar Recordings Index Page.   

Samurai Appliance Repair Man's Blog

  • entries
    819
  • comments
    1,046
  • views
    2,422,376

The Willie Method ™ for testing a microwave oven magnetron tube

Samurai Appliance Repair Man

16,793 views

Sometimes, when you're troubleshooting a microwave, it can be tricky to tell whether or not the magnetron tube is bad. In the case with many GE microwaves, the magnetron can test good according to the filament resistance specifications yet fail when you're actually trying to get the damn thing to heat up your bagel.

One of the outstanding Master Appliantologists at Appliantology.org, Budget Appliance Repair (a.k.a., Willie) offered the following procedure for assessing the operational state of the magnetron:

Disconnect the two wires going to the magtube and set it for 20-30 seconds and run it. If no abnormal noises and no smell with magtube disconnected, (MAKE SURE BOTH WIRES THAT ARE DISCONNECTED FROM THE MAGTUBE ARE SAFELY AWAY FROM EVERYTHING AND MAKE SURE NOT TO GET NEAR THEM!!!!!!!), the most likely problem is a bad magtube.

If you short the capacitor, carefully with an insulated screwdriver after doing the above test and it sparks you can be pretty sure

the magtube is bad also.

If everything else checks OK and the smell is kind of a sweet plastic burning smell, (I don't know how else to explain it but once you've smell it once you will know for sure the next time), then it's for sure a bad magtube.

Source: Advantium 220 microwave electrical burning smell

And more from another post:

Do you also notice what seems to be a louder then normal buzzing/vibrating noise.

If so, take an amp reading and see how many amps the unit is drawing, (the one I worked on only came up to around 2.4 - 2.6 amps), and you could smell that burning magtube smell after a minute or so of running.

Then pull the two wires of the magtube and make sure the are away from everything and start it up again and see what the amp reading is, (I got around 5.6 amps and the heavy vibration noise wasn't there any more).

A good working microwave will draw about 2 - 3 amps when first started and in about 3 seconds, (after the filament is warmed up), you will see the amp draw come up the the full 11 - 12 amps that a microwave will pull. If you listen carefully when a magtube ramps up power, (you will here a real light buzz noise after the filament warms up), you will see how that corresponds to the amp raise.

Source: GE OTR Microwave JVM1871SH001

  • Like 3


3 Comments


Recommended Comments

applianceman18007260692

Posted

I check the mag for continuity, if open it is bad. I check the mag for shorts between them 2 terminals and the frame of the mag. If I get a reading then it is bad. So what goes wrong?

Inside the mag is a filament like that of a light bulb. Over time the filament burns out or shorts out to the frame.

  • Like 4

Share this comment


Link to comment

Yes that's true, and sumtimes they will loose vacuume, and other times a magnet can crack.

Share this comment


Link to comment

Yea today (my 2 cents) i measured resistance on the magnetron and it was good electrically and no shorts, but then i saw that the mags magnet had a hairline crack in it and was only drawing 5.4 amps i changed it and replaced it and the diode, so then the amps were drawing about 15 amps and heating water nicely.

Share this comment


Link to comment