Isn’t it time to know what you don’t know?

Click here to check out our structured, online appliance repair training courses for rookies and experienced techs.

FAQs | Repair Videos | Academy | Newsletter | Podcast | Contact

Stay connected with us...

Samurai on Facebook - become a fan today! Sign up for our free newsletter and keep up with all things Appliantology. Subscribe to our YouTube channel for lots of appliance repair tips and help! Follow the Samurai on Twitter and get timely morsels of Appliantological Wisdom! Subscribe to our MST Radio podcast to learn secrets of the trade.

Samurai Appliance Repair Man's Blog

  • entries
    789
  • comments
    871
  • views
    2,388,875

Replacing the Drum Bearing in an LG Washing Machine

Samurai Appliance Repair Man

7,112 views

Got bad drum bearings in your LG washer and thinking about replacing 'em? Okay, Hoss, Professor john63 calls the dance steps on this little ditty:

You'll need:

REAR OUTER TUB ASSY (3045ER0048)

click on picture $ 140

Rear-Drum-with-Bearing-3045ER0048B-01050450.jpg

INNER BASKET (3045ER1017A)

click on picture $ 195

Inner-Tub-3045ER1017A-01050454.jpg

TUB O-RING SEAL (4036ER4001B)

click on picture $ 6

Tub-Seal-4036ER4001B-00697205.jpg

And a Service Manual.

http://appliantology.org/files/file/261-lg-washer-wm2487/

Source: LG washer bearing replacement?




6 Comments


Master , There is a Bearing & seal kit available on newer models & a spinner. You must have special tool,.  I also have replaced the bearing seal kit on

the whirlpool/fisher payker top loads, alot easier than replacing the whole outer tub.

Share this comment


Link to comment
Samurai Appliance Repair Man

Posted

This is great info, Dimitri!  Do you have a part number or link for the bearing and seal kit?  

Share this comment


Link to comment
dimitri77565

Posted

Sorry I had to look it all up again.  LOL Hey I live on a boat, dont keep good records. :)

 

You save about $200 clams & at least an hour in labor.   Done it only once so I took a long time .

 

http://www.repairclinic.com/PartDetail/Rear-Drum-Support/4434ER0002A/1267517

 

http://www.repairclinic.com/PartDetail/Tub-Bearing/4280FR4048L/1267500

 

http://www.repairclinic.com/PartDetail/Tub-Bearing/4280FR4048E/1267498

 

http://www.repairclinic.com/PartDetail/Tub-Spin-Seal/4036ER2004A/1267489

Share this comment


Link to comment

I realize I am replying to a 6 month old topic but this thread has been most useful to me. I have a WM2487HRM that seems to have a bad bearing. It spins OK with no load but is not balanced. Under load it wobbles pretty bad (enough that that the drum rubs the seal so much it starts to smoke). I have removed the tub unit from the machine and trying to separate the back half from the inner tub but the bearing seems to be holding it in place.

 

 How do you pull the bearing?  There is mention of a special tool above, do you have a link?

 

 Here are some photos of where I am at now ...

Share this comment


Link to comment

OK, I got past the above issue. I just needed to stack the outer tub (back half) on some braces so the inner tub was off the ground a bit and then I just used a dead blow hammer on the spindle in order to push it through the bearings. I was also able to pop the bearings out of the back half of the outer tub with a chisel and same hammer.

 

So I figured I just needed to get the spider arm off the back of the inner drum (you can see photo #3 in above album) and then I would be all set and ready to order the pieces mentioned by Dimitri. Unfortunately I have not been able to remove 2 of the 6 bolts off that retain the spider arm to the inner tub. These 2 bolts turn with much effort but are not coming out like the others. It feels like there may be bolts on the other side but I cannot see as the inner tub seems to have layers also. I will see tomorrow if there is any way to get those 2 nuts out but at this point I probably will just order these parts for my repair:

 

+ Inner Basket   3045ER1017A

+ Tub Bearing (inside)  4280FR4048L
+ Tub Bearing Seal   4036ER2004A
+ Tub Bearing (outside) 4280FR4048E

+ Tub O-Ring Seal 4036ER4001B

 

Any ideas on getting those 2 bolts free would be appreciated but it looks like my inner tub has some rust and corrosion on it anyways (although it may clean up if I spent time on it). If I can get those last bolts off the spider arm then I would probably go back to just getting the spider arm instead of the whole inner tub.

Share this comment


Link to comment