Jump to content
Click here to check out our structured, online appliance repair training courses for rookies and experienced techs.

FAQs | Repair Videos | Academy | Newsletter | Podcast | Contact

Stay connected with us...

Subscribe to our YouTube channel for lots of appliance repair tips and help! Subscribe to our MST Radio podcast to learn secrets of the trade. Sign up for our free newsletter and keep up with all things Appliantology.

All Activity

This stream auto-updates     

  1. Past hour
  2. Today
  3. William Lewis

    Dacor Wall Oven MOV230S service manual

    Thanks needed this
  4. William Lewis

    GE ZV750SY4 Vent Hood Minimanual

    Thanks needed this
  5. evaappliance

    Whirlpool WED4800XQ1

    Yep , also if you know for sure the element is good , you can see if it heats on air fluff, if it does, odds are It will be the afore mentioned relay.
  6. Uses this service manual!
  7. Scottekarate

    Whirlpool WED4800XQ1

    Unplug your dryer. Remove the top. You'll see the main control on the left. Remove the two or three screws, squeeze and push the black plastic wire retainers and rotate the bracket to where you can see the board. Look for the red and black wires going to your heat relay. Unplug the two wires and check for continuity. You should read an open circuit. If you have continuity, replace the control.
  8. Yesterday
  9. Rob Fowler

    GE Electric Range tech sheet

    There is a training bulletin if you search for JB750* you will find it.
  10. darren412

    Maytag washer won't fill

    Get the tech sheet like rob said . run the manual diagnostic test and see if the cold and hot test will work for each valve. If one or both do not work and let the correct selection of water in for the test sequence, then I would look into the mixing valve for the washers house plumbing as possibly being your issue like scottkarate mentioned.Those hot and cold mixing valves do not have a good record for reliability in my opinion. Leave one hose on and disconect the other off the washer and put it into a 5 gallon bucket then turn on the valve. if hot or cold wter gushes out for the hose selected then re install that hose to the washer and repeat the process with the other hose.
  11. Have you cheked Have you checked the heating element to see if its grounding out against the heater housing ? or the motor may possibly be junk and drawing to much amperage for some reason. When ever I run into an issue with any appliance that trips the circuit breaker I will always run a good extension cord to on a separate receptacle on a different breaker first and try that. The majority of times I do that , its always been the wall receptacle that has the issue. especially if they just installed one of those new arc fault breakers in the panel. Ive seen dishwashers that run just fine pop those types of breakers.
  12. thank you.I knew this was gonna be bad
  13. I changed the cord twice and the outlet checks out.
  14. until

    You need to fill out the linked form above in the "Where" section of the event description and the connection details will be automatically sent to you. Be sure to watch the video above. And for best results, download the free Join.me app instead of connecting through your browser. It's very straight forward and the short video above gives you a good idea of what to expect.
  15. MrApplianceMatt

    Whirlpool GEW9200LW1 dyer with an electrical short

    What about the actual appliance cord or the wall socket? Is it possible there's an issue in either one of those that doesn't manifest itself until the dryer is plugged in?
  16. I read this model number directly off the appliance. It does not seem to show up on Repair Clinic; However, it does on searspartsdirect.com. Haven’t found any tech sheet on the appliance or anywhere online, so anything we can get would be much appreciated. Thank you!
  17. I have a front loading Whirlpool GEW9200LW1 that blows the circuit breaker as soon as I plug it into the outlet. I have checked every wire and component for continuity and resistance. I also visually checked every wire and circuit board but I cannot find any short. I took the unit completely apart any pulled all the wiring. I started with the main wire harness (WP8576530) installing it in the dryer without connecting the components. When I plugged in the dryer, the circuit shorted out. I found if I disconnected the ground wire attached to the bottom of the dryer between the out exhaust pipe and the heater, I can connect the dryer to the outlet without the tripping the circuit breaker. Any thoughts where the short might be?
  18. Haier 2017 15 Cu. Ft. French Door Bottom Freezer Service Manual View File Models HRF15N3AGS HRF15N3BGF PUB 31-9270 Submitter Samurai Appliance Repair Man Submitted 10/17/2019 Category Appliance Repair Manual Pot Luck Supper  
  19. Version 1.0.0

    2 downloads

    Models HRF15N3AGS HRF15N3BGF PUB 31-9270
  20. Version 1.0.0

    1 download

    Models CDE06RP2NBS1 CDE06RP3NBD1 CDE06RP4NBW2 DD410RS PUB 31-9288
  21. GE Café & Haier Built-In Dual Drawer Refrigerator Service Manual View File Models CDE06RP2NBS1 CDE06RP3NBD1 CDE06RP4NBW2 DD410RS PUB 31-9288 Submitter Samurai Appliance Repair Man Submitted 10/17/2019 Category Appliance Repair Manual Pot Luck Supper  
  22. Samurai Appliance Repair Man

    kenmore refrigerator service manual needed

    This is a Haier-built unit. Would need to cross over to a Haier OEM model number. Also, looks like many key parts on this model are NLA-- not a good sign.
  23. Fisher & Paykel DD24D V2 DD24S V2 Dishwasher Service Manual View File PUB 590134 - SEPTEMBER 2010 Submitter Captain Dunsel Submitted 10/17/2019 Category Appliance Repair Manual Pot Luck Supper  
  24. Version 1.0.0

    1 download

    PUB 590134 - SEPTEMBER 2010
  1. Load more activity
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.