Search the Community

Hello all! First time poster so forgive my noob mistakes. I have a whirlpool 5 door fridge that I’m flipping, or was the plan. The lady I got it from said that the freezer froze over and then the door alarm wouldn’t stop going off. I’ve checked the freezer section and I can’t find any indication that it ever froze over. I can however find that the eBay fan in the refrigerator section is not running and not getting power. From what I believe is due to the door switch. to date: ive probes all the leads. No power to evaporate fan. door switches all tested out with correct ohms. But the voltage is at 6, not 120 as information suggests it should be. I’ve replaced 3 of the 5 door switches. Still nothing. I’ve tried jumping/bypassing the last two remaining door switches, still a no go. the pantry door control is functioning as expected, and I read where one could disconnect the pantry door and this would correct the situation. Not with this unit! I’ve traced pantry control wiring back to where it enters the wall of the unit. Unhooked it deom that junction and inspected each wire for breaks, nada! tge LED lighting turns off after 5 minutes. And I have to unplug it and reconnect before they will come back on. the refrigerator will not run (compressor) unless I put it into test mode and then take it out manually. Once I do this I can get the compressor to turn on and start cooling. But of course the wrap starts to freeze over after a few minutes because the evap fan isn’t working. I’m on the third evap fan! The first one was dead, the second one was DOA and now this one. That so far tests out. I’ve actually started to use another fan, just as a crash test dummy so if it is the board drying them it will dry an old computer cooling fan and I’ll still have the good fan. Lol. im at a loss. The aurora board is mentioned in a few posts out there. I’ve inspected it connection by connection. But nothing has been discovered. On boards like these I generally repair them, since I’m not in a position for parts markup. The main board I’ve proved as well. Power is at all the proper points, but even this board I’ve tested and nothing. Any ideas on what to check next. Aside from my blood pressure and my insanity level. This unit is becoming my arch nemesis. I would normally walk away from it, and have 3 times already. But my sister seen it and now she wants it. Can anyone help With a service manual or any advice??? if I’ve left out anything or if you have questions for me, please post them here and I’ll respond ASAP. thanks so much for allowing me to be a part of the site. ~DIYChick

Just noticed that all five knobs were out this morning. All burners still ignite just fine. The unit was purchased January 2019 and we have been super happy with it. While not a necessary feature, the backlit knobs were nice looking and did remind you the unit was on if you walked away from a summer, etc. I called Miele and they can't help diagnose any longer unless you are a certified tech and it was just a one year warranty so paying $100 for a visit plus time and any parts didn't seem worth it for just the LED ring lights. I did pull it today and took it halfway apart. Verified 110 voltage in a few spots, but couldn't get a bead on the 12V. There was a board that looked like it converted the voltage and another unit mounted in a more difficult spot to get to. All wires looked good. If there is any easy diagnosis I can do, electrical/circuit diagram, or troubleshooting guide that would be great. Any help appreciated!

I have recently moved. The refrigerator, before the move, was great...no problems. Now I am at the new house, refrigerator is in the garage, and I am looking to sell it as the new house already had build-ins. When I plugged in the old refrigerator (about 9 years old), the compartments have stayed warm, the temperature control panel stays on temporarily when I set the levels then shuts off, and the refrigerator side lights won't come on....freezer lights are fine. fan seems to be working. i do not have the water line attached since the fridge is in the garage so not sure if that helps with the refrigeration process or not. as I am looking to sell the refrigerator....and its in great shape...it doesn't make sense for me to have repairman come out ($$) and then replace potentially small part or simple fix ...if I can do myself. But maybe its not that simple. Looking at online videos, seems like it goes back to the mutha board, but not sure where I would start to test. any help is appreciated. troy