Jump to content
Click here to check out our structured, online appliance repair training courses for rookies and experienced techs.

FAQs | Repair Videos | Academy | Newsletter | Contact

Stay connected with us...

Subscribe to our YouTube channel for lots of appliance repair tips and help! Subscribe to our MST Radio podcast to learn secrets of the trade. Sign up for our free newsletter and keep up with all things Appliantology.

Search the Community

Showing results for tags 'symptoms'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • Appliantology Welcome Center
    • Site Orientation
    • Announcements
  • DIYer Appliance Repair Forums
    • DIY Appliance Repair Help
    • Appliance Haikus
  • Appliance Tech Job Board
    • Looking for a Tech?
    • Looking for a Job?
  • Appliance Service Manual Requests
    • Appliance Service Manual Requests Forum
  • Professional Appliance Technician Forums
    • Appliance Repair Tech Forum
    • Professional Appliantologist Webinars Forum
    • Samurai's Appliance Repair Video Classroom
    • Samurai’s Appliance Puzzles
    • The Dojo


  • Samurai Appliance Repair Man's Blog
  • kdog's Blog
  • Mrs. Samurai's Kitchen
  • DurhamAppliance's Blog
  • applianceman97's Blog
  • LI-NY Tech's Blog
  • tpoindexter's Blog
  • Eugene's blog about stores, fixing, life, and more!
  • Appliance Repair Tech Tips


  • Appliance Repair Manual Stash Access File®
  • Appliance Repair Manual Pot Luck Supper

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...

Found 1 result

  1. Got a confusing problem. Here's what I know about the Regular cycle: Fills and drains fine, both water temperatures, but the drum doesn't rotate slowly in either direction, in any part of the cycle. It does not move at all until the final spin. The final spin works as normal, slowly clockwise for a few seconds, then fast clockwise for about a minute (when empty) then coasting to a stop. There is also no slow rotation in either direction after the final spin has come to a stop, which it used to do. In short, the drum and motor don't move except for the final spin. Here's what I know about the various parts: The door lock seems to be fine: the "door lock" light comes on, there's no change when I push in on the door, and the solenoid isn't buzzing like it does when the door is not fully closed. The drain pump runs (I can feel it vibrating) appropriately, the tub drains fine, and good flow rate exits the discharge tube. Final buzzer works normally and sounds at the correct time. The motor speed controller is highly suspect except that I can hear the relays clicking on it at all the times the drum should be changing directions. The tech sheet I found inside the cabinet includes a series of diagnostic steps for "motor will not run" so I went through them even though it spins fine, and some of the steps are strange, others bizarre. For example, step 3 says to measure voltage between pins 2 & 4 of the 4-pin, and you get no voltage suspect the motor thermal cut out. I got 0 V, but it can't be the motor thermal cutoff because the motor runs fine for the final spin. Bizarrely, step 5 suggests checking voltage between pin 3 on the 9-pin plug and pin 4 of the 4-pin plug. Well there IS no pin 3 on the 9-pin plug; it's an empty hole, no wire there! I got no voltage on any combination of pins on the 4-pin plug when the cycle was beginning (but empty of both clothes and water, per the instructions on the tech sheet), which would be relevant except that the motor isn't supposed to run when there's no water in there yet. I'm thinking the tech sheet is just wrong or poorly written. The belt is in great shape; tight, good contact, no hot smell, all good. Drum suspension seems good; drum moves smoothly (but not excessively) in all directions, nicely balanced, no banging. Timer feels normal when turning it. Bottom line: I suspect the motor speed controller and/or the timer, but which, and how to tell? There are no error-code LEDs on this machine. I suppose it could also be the motor if there are different windings for slow speeds, or something else I've never heard of. Help!! (and thanks)
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.