tech1911 Posted January 19, 2010 Share Posted January 19, 2010 Requesting a service manual for this, sorry excuse of a washer! model# WWSE5240G0WW Thanks Link to comment Share on other sites More sharing options...
RegUS_PatOff Posted January 19, 2010 Share Posted January 19, 2010 31-9040 service manual may be similarlink PM'd Link to comment Share on other sites More sharing options...
tech1911 Posted January 19, 2010 Author Share Posted January 19, 2010 The model I am working on has a inverter board on the motor. I dont think that manual will be accurate to help diagnose this washer. If you have a manual that has the inverter board on the motor, I would appreciate it. Thanks for your help Link to comment Share on other sites More sharing options...
RegUS_PatOff Posted January 19, 2010 Share Posted January 19, 2010 yes, i'll have to look for the manual if you'll still need itbut here's some other infoRegUS_PatOff wrote: .....&%^$#&&^## GE model numbers ..http://fixitnow.com/wp/2009/11/10/ge-hydrowave-top-loading-washer-wont-run/GE Washer Inverter Motor Error Codes.pdfhttp://applianceguru.com/forum2/21714-1.html Link to comment Share on other sites More sharing options...
tech1911 Posted January 19, 2010 Author Share Posted January 19, 2010 I do still need the manual if you can find it. I have the inverter board status light codes, but I do not believe the motor is bad (2 blinks), and the belt is not slipping. Link to comment Share on other sites More sharing options...
appl.tech.29501 Posted January 19, 2010 Share Posted January 19, 2010 I think I have your cure but notes are at my house, I will post back when I get home Link to comment Share on other sites More sharing options...
RegUS_PatOff Posted January 19, 2010 Share Posted January 19, 2010 maybe this one 31-9145 link PM'd[align=left]Profile Washers With Electronic Control and Mode Shifter Assembly[/align]WPRE6100WPRE8100 Link to comment Share on other sites More sharing options...
appl.tech.29501 Posted January 19, 2010 Share Posted January 19, 2010 2 flashes means that the tub hub nut is loose. Tighten nut and to clear fault disconnect power to washer for 15 seconds, reconnect power and open and shut the lid 5 times within 30 seconds Link to comment Share on other sites More sharing options...
tech1911 Posted January 20, 2010 Author Share Posted January 20, 2010 Thanks. I had already replaced the hub nut, old one threads were stripped and tub loose. Then it would fill and drain only. I did not clear the code, will do tomorow. Will this POS machine not agitate or spin if the problem was fixed, but code was not cleared? Link to comment Share on other sites More sharing options...
RegUS_PatOff Posted January 20, 2010 Share Posted January 20, 2010 [user=60379]tech1911[/user] wrote: ... Will this POS machine not agitate or spin if the problem was fixed, but code was not cleared?NOTES:ERROR ##4 The Motor continues to operate with this error.#6 When a locked Rotor is detected, the Washer will sit idle for 15 seconds and retry.If the Motor does not operate after 3 tries, the LED blinks 6 times.#8 The Motor continues to operate at reduced performance levels.#9 Maximum Spin speed is limited to 50 RPM.Critical Errors, #1, #2, & #7, will prevent Inverter/Motor from operating.To clear errors, disconnect power until a clicking sound is heard (approximately 15 seconds).Open and close the Lid 5 or more times in any 12 second period within the first 30 seconds of power-up.Errors will not clear if Washer is in either Agitate or Spin mode. Link to comment Share on other sites More sharing options...
tech1911 Posted January 20, 2010 Author Share Posted January 20, 2010 Thanks for your help Link to comment Share on other sites More sharing options...
Recommended Posts