Lost with the new appliances? The Samurai teaches you Circuit Fu…

Click here to check out our structured, online appliance repair training courses for rookies and experienced techs.

FAQs | Repair Videos | Academy | Newsletter | Podcast | Contact

Stay connected with us...

Samurai on Facebook - become a fan today! Sign up for our free newsletter and keep up with all things Appliantology. Subscribe to our YouTube channel for lots of appliance repair tips and help! Follow the Samurai on Twitter and get timely morsels of Appliantological Wisdom! Subscribe to our MST Radio podcast to learn secrets of the trade.
  • Announcements

    • Samurai Appliance Repair Man

      Webinar Recordings Index Page   07/27/2017

      One of the benefits of your Professional Appliantologist membership is that you can attend the regular, live training webinars and you have access to the recordings as well. So if you can't make it to the live webinar, catch the recording at your convenience. The webinar recordings are conveniently listed for you on the Webinar Recordings Index Page.   
tpwu

GE ACM24DAT1 Window AC no cold air

Recommended Posts

tpwu   
tpwu

Dear masters,

My Window A/C out of sudden is not blowing cold air any more and I couldn't hear the compressor running. I checked the thermostat with ohm meter and got close to 0 reading. It seems good.

I checked its capacitor (labeled 45+5uf-3+6%) and got 41.6uf and 5uf for Herm and Fan repsectively. Would 41.6uf be too low causing the problem? or something else?

Your kind help is always appreciated.

Share this post


Link to post
Share on other sites

Need appliance parts? Call 877-803-7957 now!

Bobice   
Bobice

Did you check the overload on the compressor ? Did you test the compressor with the ohm meter. Do this remove the cover from compressor and with meter set to Rx1 touch each terminal with one meter and the other lead to the "shell" of the compressor. Get a reading ? winding is grounded. Then hold meter lead to one terminal and other lead to each other terminal to see if winding is open.

Share this post


Link to post
Share on other sites
Bobice   
Bobice

Inspect the compressor's electrical terminals. Do this by turning off the electricity at the disconnect box. Then remove the cover to gain access to the compressor. In some cases, the fan is connected to the cover. The fan has enough extra wire to allow it to be moved without disconnecting it. Pry open the compressor terminal cover. Check the connections for melted terminals. Melted terminals are a sign of compressor failure.

Test the compressor for a short. First, mark each wire to make re-installation easier. Then remove the wires from the compressor. Turn the multimeter to ohms. Touch the leads together. The meter should beep. Touch one lead to the compressor case, then touch the other lead to each terminal. If the meter beeps at any terminal, then a short is in the compressor. Check the compressor for continuity with the ohm meter. Touch one terminal with one lead. Press the other lead against the other terminals. Do this for every combination. There should be continuity between each. If there isn't, then the compressor is bad.

Edited by Bobice

Share this post


Link to post
Share on other sites
tpwu   
tpwu

Thanks for the detail instructons. The unit is quite heavy for me and is mounted in a wall. I need to get a helper to take it apart. However, by referencing the wiring diagram attached on the unit, I measused the wires and got the readings R-S:3.1, C-S:2.1 and C-R:1.3. I recall the unit tripped the circuit breaker once few days ago. Would the compressor be bad if both capacitor and thermostat are good?

Share this post


Link to post
Share on other sites
applianceman18007260692   
applianceman18007260692

Unplug it and check between the 2 hot prongs on the cord to the frame. If you get a reading you have a short. Slide out the innards enough to remove the cover off the compressor and look for a burnt wire like Bobby said.

Share this post


Link to post
Share on other sites
tpwu   
tpwu

Pulled it out half way and measured all three contacts against the case of the compressor, luckly there are no readings on them.

And there are readings between contacts.

Share this post


Link to post
Share on other sites
applianceman18007260692   
applianceman18007260692

If ya ain't got no shorts piggy back a hard start on the existing cap to give the compressor an extra boost.

Powerstart Hard Start HVAC Booster for SRP6 HS650 WSX-6

Share this post


Link to post
Share on other sites
tpwu   
tpwu

My unit is 24000 BTU and the booster is suitable for compressor 4000 and 12000 BTU, isn't it.

Is the orignal capacitor still good?

Share this post


Link to post
Share on other sites
applianceman18007260692   
applianceman18007260692

Replace the capacitor and see. It should read 45 mfd's on the herm to common side. If it is reading 41 it might not be strong enough to get that compressor going.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now