Jump to content
Click here to check out this guide.

FAQs | Repair Videos | Academy | Newsletter | Contact


DISCLOSURE: We may earn a commission when you use one of our coupons/links to make a purchase.
  • Upcoming Events

    • 27 April 2024 02:00 PM Until 03:00 PM
      5  
      All Appliantology tech members are invited to join in this workshop on all things Appliantological. 
      We have a special session planned for this one. Instead of the usual Show 'n Tell on a technical topic, we're going to post tech sheets in the comments to this Calendar Event (scroll down to see what's posted so far) and ask specific questions that can only be answered by reading the tech sheet. If you at least try to answer the questions beforehand, you'll get a lot more out of it. The tech sheet and the questions are posted in the comments section below.
      Your mission, if you should choose to accept it, is to check out the questions for each one and try to answer them ahead of time. Then come to the Dojo to see how well you did! 
      Who: This workshop is only available to tech members at Appliantology.
      When: Saturday, April 27 @10:00 AM Eastern Time.
      Where: Online via Zoom
      How:
      Click here to go to the forum topic with the registration link. If you're interested, register now. Arrive a couple minutes early to make sure your connection is working. Set a reminder for yourself for this workshop so you don’t miss it.  And check out past workshops here: https://appliantology.org/announcement/33-webinar-recordings-index-page/

Noritz Model GT-201AW-FF water heater (for Japanese bath)


hdheetderks

Recommended Posts

I need a replacement main circuit board (it has the micro processor and a bunch of interface circuits) for this unit.

This model has never been sold in the US. I bought it in Japan. It is specially designed for Japanese style bathtubs and includes a separate 50,000 BTU heater with a recirculating pump which keeps the water in your tub steaming hot. It also has a water level detector so that it automatically refills the tub as you scoop water out of it as is done in the Japanese style of bathing.

Now the processor board has been blown out due to one of the electrolytic capacitors leaking juice which ate off a ground line on the PCB and caused the logic board to see -30 volts from the fan motor control circuit.

Any ideas as to how I can get a new main board for this thing?

I have made a very good circuit and functional diagram of the unit, and made a number of measurements regarding the operation of various subsystems if anyone would have any interest in them.

Henry Heetderks

hdh@ssl.berkeley.edu

Link to comment
Share on other sites

  • Replies 3
  • Created
  • Last Reply

Top Posters In This Topic

  • RegUS_PatOff

    2

  • hdheetderks

    2

Top Posters In This Topic

For the Noritz GT-201AW-FF Japanese bath tub and water heater. Here are some pictures:

ftp://sprite.ssl.berkeley.edu/pub/hdh/Noritz_GT-201AW-FF_Pictures/P1000493.JPG shows the disassembled unit on the bench for electrical testing. The circuit board slightly to the left of the center of the picture is what I have to replace.

ftp://sprite.ssl.berkeley.edu/pub/hdh/Noritz_GT-201AW-FF_Pictures/P1000501.JPG shows the unit assembled and installed in the crawl space under my house. Note the 120 to 100 volt transformer just visible at the top right of the picture.

ftp://sprite.ssl.berkeley.edu/pub/hdh/Noritz_GT-201AW-FF_Pictures/P1000506.JPG shows the unit with the front cover in place.

ftp://sprite.ssl.berkeley.edu/pub/hdh/_hdh_dwgs/Drawing_File/0203-AC14-E.dwg is a detailed circuit/block diagram of the system. This drawing is in AutoCAD14.

ftp://sprite.ssl.berkeley.edu/pub/hdh/_hdh_dwgs/Drawing_File/0204-AC14-C.dwg is a schematic for the fan motor controller board.

ftp://sprite.ssl.berkeley.edu/pub/hdh/_hdh_dwgs/Drawing_File/0210-ME02-A.xls

ftp://sprite.ssl.berkeley.edu/pub/hdh/_hdh_dwgs/Drawing_File/0211-ME02-A.xls

ftp://sprite.ssl.berkeley.edu/pub/hdh/_hdh_dwgs/Drawing_File/0212-ME02-B.xls

ftp://sprite.ssl.berkeley.edu/pub/hdh/_hdh_dwgs/Drawing_File/0213-ME02-A.xls

ftp://sprite.ssl.berkeley.edu/pub/hdh/_hdh_dwgs/Drawing_File/0214-ME02-C.xls are all Excel files which record measurements made on the system.

I think what I really need is someone who has access to Noritz parts. I don't see Noritz even listed on the fixitnow parts finder.

Henry Heetderks

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...