Clicky

Jump to content
Click here to check out our structured, online appliance repair training courses for rookies and experienced techs.

FAQs | Repair Videos | Academy | Newsletter | Podcast | Contact

Stay connected with us...

Subscribe to our YouTube channel for lots of appliance repair tips and help! Subscribe to our MST Radio podcast to learn secrets of the trade. Sign up for our free newsletter and keep up with all things Appliantology.

todd5pt0

Whirlpool GC900PPB6 Trash Compactor will not reverse

Recommended Posts

todd5pt0

I have a Whirlpool GC900PPB6 Trash Compactor that is 14 months old and off warranty.  When I push Start button, the ram will lower down to the bottom of the cycle and stop.  At this time the compactor makes a metal grinding noise.  It will not reverse and move up.  I have it torn down and have cycled the ram down several times.  I have to manually turn the gear on the bottom to get the ram back up to the top position.  I have tested the motor and centrifugal switch with an ohm meter according to the tech sheet found inside the compactor.  Can't figure out what is wrong.  

Share this post


Link to post
Share on other sites

Need appliance parts? Call 877-803-7957 now!

Richard Demint

Need to test all switches on this, top and bottom. the most common thing to go wrong on these is the switch in the motor or your top limit directional switch. Keep testing and you will find it.

  • Like 1

Share this post


Link to post
Share on other sites
evaappliance

Make sure the gears are not stripped, if the moter doesn’t stall at the bottom it will not reverse 

Share this post


Link to post
Share on other sites
todd5pt0

Thanks for the advice.  Is it the top limit switch that senses the stall and reverses the motor?  I broke the top limit switch when I was taking the ram out while troubleshooting.  I have a new switch on order.  

Share this post


Link to post
Share on other sites
evaappliance

I’m not positive, but I don’t think it will be the top switch. The last one I did was doing the same thing and it was this , WP9870037. I put these and power nuts on .  I agree that if it is a switch it will be the moter switch but if it is not stalling at the bottom look into these other parts . 

Share this post


Link to post
Share on other sites
todd5pt0

I was looking at those power stops on my compactor while the ram was going down.  So the theory is the power stop is too short and ram goes down too far?  The pin and speed nuts on the power nuts were loose.  I replaced those with bolts and nylon nuts thinking the power nuts were binding because they were loose.

Share this post


Link to post
Share on other sites
todd5pt0

I also took the ram out and cycled the ram screws forward and reverse by manually flipping upper limit switch.  There was no hesitation or grinding in the motor as it reversed direction.  My problem has to be ram related.

Share this post


Link to post
Share on other sites
evaappliance

if the top of the stops are (mushroomed ) out then they need replaced , but if you have already replaced the power nuts then my theory may not be the answer  

Share this post


Link to post
Share on other sites
todd5pt0

I flipped the compactor on it's side and watched the gear set on the bottom while cycling the machine.  Sure enough the small gear is spinning on the large gear.  I have ordered a replacement gear set.  Thanks so much for all the repair advice.

Share this post


Link to post
Share on other sites
evaappliance

I have seen a couple do that !  great catch ! 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.