Jump to content
Click here to check out this guide

FAQs | Repair Videos | Academy | Newsletter | Contact


DISCLOSURE: We may earn a commission when you use one of our coupons/links to make a purchase.
  • Upcoming Events

    • 09 November 2024 03:00 PM Until 04:00 PM
      3  
      All Appliantology tech members are invited to join in the conversation for all things Appliantological: bidness, customers, tools, troubleshooting, flavorite brewski, whatever. Webcams and microphones are open and live!
      This event is also a great time for any students at Master Samurai Tech to bring any and all questions about the coursework. We're happy to walk through any concepts you're having trouble with. Think of it like office hours with your teachers. 
      Also, follow the Calendar Event so you'll get notified of new posts here. Look for the "Follow" button either at the top of the topic on desktop or below the topic on mobile.
      Who: This workshop is only available to tech members at Appliantology.
      When: Saturday, November 9 @10:00 AM Eastern Time.
      Where: Online via Zoom
      How:
      Click here to go to the forum topic with the registration link. If you're interested, register now. Arrive a couple minutes early to make sure your connection is working. Set a reminder for yourself for this workshop so you don’t miss it.  And check out past workshops here: https://appliantology.org/announcement/33-webinar-recordings-index-page/

Kitchenaid KUDS24SEAL5 Dishwasher spray arm wobbles.


pjw73nh

Recommended Posts

Greetings,  my KUDS24SEAL5 was not cleaning very well.  I noticed the lower spray arm was VERY wobbly.  It spins freely, but is VERY wobbly.  Yesterday, I replaced the washer arm bearing (WP9742946) which was worn paper thin. 
 
I also replaced the split ring bearing (WP3376846) on the bottom of the spray arm as well.  Though not part of this discussion, I replaced the split ring bearing on the upper washer arm as well.
 
I have only run one small load since, and it appears to clean better.  Too early to tell at this point.
 
One thing that bothers me is that even after replacement of the lower washer arm bearings, the spray arm was VERY still wobbly.  I didn't expect it to be.  The spray arm has what I would estimate to be 1/8" - 3/16" axial play if I pull directly up on the spray arm. 
 
How wobbly should this spray arm be?  Is there a clearance spec for it? Could the flange on the spray arm nut be worn so much to allow this wobble, or is the wobble normal? It doesn't look worn at all.
 
Thanks. 
Link to comment
Share on other sites

  • Replies 2
  • Created
  • Last Reply

Top Posters In This Topic

  • pjw73nh

    2

  • evaappliance

    1

Popular Days

Top Posters In This Topic

Think this is normal movement , cleaning out the filter at the chopper assembly will help most of the time. Should be able to find a u tube video on how to get to it.

Link to comment
Share on other sites

Thank you for confirming this Eva,  While I had the arm off, I took it down to the motor assy.  Cleaned and inspected everything in between.  All looked good. The impeller nut was b1+ch to get off.  I had to use a 1" socket with vice-grips to hold the socket, and then put my nut-driver down in the drive hole of the socket.   To my knowledge it had never been removed.  Washer is about 16 years old. 

It appears, when I cleaned it all op, I loosened a bunch of black "gookus".... the first washer after the cleaning left a lot of black "gookus dots on the dishes.  One more wash took care of them. I suspect just jeft over debris I loosened up.

Thanks for the reply. 

P.../NH

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...