Jump to content
Click here to check out this guide

FAQs | Repair Videos | Academy | Newsletter | Contact


Search the Community

Showing results for tags 'circuit board'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Appliantology Welcome Center
    • Site Orientation
    • Announcements
  • Professional Appliance Technician Forums
    • Appliance Repair Tech Forum
    • Master Samurai Tech Workshops
    • Samurai's Appliance Repair Video Classroom
    • Samurai’s Appliance Puzzles
    • The Dojo
  • Appliance Service Manual Requests
    • Appliance Service Manual Requests Forum
  • Appliance Repair Trade Resources
    • Looking for a Tech
    • Looking for a Job
    • Appliance Repair B2B Resources
  • DIYer Appliance Repair Forums
    • DIY Appliance Repair Help
    • Appliance Haikus

Blogs

  • Samurai Appliance Repair Man's Blog
  • kdog's Blog
  • Mrs. Samurai's Kitchen
  • DurhamAppliance's Blog
  • applianceman97's Blog
  • LI-NY Tech's Blog
  • tpoindexter's Blog
  • Eugene's blog about stores, fixing, life, and more!
  • Appliance Repair Tech Tips
  • Koi Guy's Amazing Compendium of Timeless Appliantological Wisdom
  • Rhubarb Tau's Sloggy Vlog Blog Bog

Categories

  • Appliance Repair Manual Stash Access File®
  • Appliance Repair Manual Pot Luck Supper

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Found 4 results

  1. Mostly just curious if anyone here has attempted any board level repairs. I am specifically looking at a GE Hydrowave motor control board which was giving me a red LED flashing 6 times after being reset a handful of times with and without the belt. The used replacement has the washer going again, but this board is the only apparent reason it failed since the motor seems fine. Can someone tell me if the service manual for a GTWN4450M1WS (https://appliantology.org/files/file/693-ge-gtwn4250d0ws-top-loading-hydrowave-washer-minimanual-and-service-bulletin-bundle/) would give me anymore information on the motor than what I have already? I really doubt a schematic of that board exists in any public capacity. I cant download it ...
  2. Starting a week or so ago occasionally herd a fan 'cycle'...run for 2-3 seconds, then spin down and immediately back up. As of today it's doing it constantly. I have cleaned out the condenser coils and verified that its the condenser fan making the noise, I have run the diagnostic test #49 as mentioned in another post and it cycles at around 1700-1750, but it will dip to +/- 0, 420, 1200 mostly it stays in the 1700 range. I believe it to be the circuit board as the main problem and possibly the fan, but it does spin based on the reading on this site and others. I plan on replacing the circuit board and fan at the same time. If my logic is off please let me know. When replacing the circuit board, is it just a plug in and replace or is there any type of setup/programing that needs to happen Any help or insight would be greatly appreaciated Mike
  3. Hi All, My Westinghouse RS645T fridge water dispenser is not working. When I wasn't home it blew the circuit breaker so I am not sure if it just file or went out with a bang. When I got home I could smell burnt electronics, just didn't know what/where until I went to get some water! The lights on the front control panel do not work. When I press the switch to dispense the water the solenoid operates and the light turns on, but no water or ice. I was wondering where the controlling board is housed and how I get to it to replace? Really appreciate any assistance. Thanks Dave
  4. Samurai Appliance Repair Man

    Tips For Repairing A Burned Circuit Board

    From the album: Miscellaneous

    Even though a burned circuit board can look really gnarly, it's usually repairable.
×
×
  • Create New...