Jump to content
LIMITED TIME OFFER: Get up to $100 off tuition for Master Samurai Tech courses through November 30th ×
Click here to check out this guide

FAQs | Repair Videos | Academy | Newsletter | Contact


DISCLOSURE: We may earn a commission when you use one of our coupons/links to make a purchase.

  • Upcoming Events

    • Appliantology Live Dojo, Saturday, 11/23/2024 @10 AM ET
      23 November 2024 03:00 PM Until 04:00 PM
      2  
      All Appliantology tech members are invited to join in the conversation for all things Appliantological: bidness, customers, tools, troubleshooting, flavorite brewski, whatever. Webcams and microphones are open and live!
      This event is also a great time for any students at Master Samurai Tech to bring any and all questions about the coursework. We're happy to walk through any concepts you're having trouble with. Think of it like office hours with your teachers. 
      Also, follow this Calendar Event so you'll get notified of new posts here. Look for the "Follow" button either at the top of the topic on desktop or below the topic on mobile.
      Who: This workshop is only available to tech members at Appliantology.
      When: Saturday, November 23 @10:00 AM Eastern Time.
      Where: Online via Zoom
      How:
      Click here to go to the forum topic with the registration link. If you're interested, register now. Arrive a couple minutes early to make sure your connection is working. Set a reminder for yourself for this workshop so you don’t miss it.  And check out past workshops here: https://appliantology.org/announcement/33-webinar-recordings-index-page/

GSS23WSTA SS Dispenser flashing 00

bubba153

By bubba153
in DIY Appliance Repair Help

 Share

Recommended Posts

bubba153

bubba153

Posted
Posted

Hi

     I noticed this morning that the water dispenser was not working. It worked fine before. . I also pressed the temperature button and it was reading 13/40. I do not see any frost on the back panel but I didn't take it off .usually that has frost on it when the coils are iced up   Last week I had replaced the heater as the defrost was not working and it was then working perfectly 0/36 until now.

I checked the defrost and thermastat and all were closed. I checked the thermistor and that was 26k ohm.    I had a spare board so I thought it was the board so I replaced that. when I plugged in the unit I would hear the compressor kick in and went to the dispenser and it was 2 set of 00 flashing. at first I thought it was just resetting itself like a modem but it hasnt stopped.

  I looked on line was said to hold all 4 buttons down for 10 seconds so I did and it beeped and went to alternating 0 side to side.  

most of the dispenser buttons wont light. Ice ,water etc    no green light

 

Is there another board in the dispenser that went bad?  

 

Any help greatly appreciated

 

Thanks

Wayne

 

  • Replies 5
  • Created
  • Last Reply

Top Posters In This Topic

  • Chat_in_FL

    2

  • 16345Ed

    2

  • bubba153

    1

  • Hiroshi

    1

Popular Days

Top Posters In This Topic

Popular Days

Chat_in_FL Sensei

Chat_in_FL

Posted
Posted

Tech Manual submitted to Potluck awaiting approval:

Profile SxS with electronic controls 31-9072.pdf

16345Ed Sensei

16345Ed

Posted
Posted
3 hours ago, Chat_in_RI said:

Tech Manual submitted to Potluck awaiting approval:

Profile SxS with electronic controls 31-9072.pdf

Diyers don't have access to professional forums and manuals...

Chat_in_FL Sensei

Chat_in_FL

Posted
Posted
11 hours ago, 16345Ed said:

Diyers don't have access to professional forums and manuals...

Was kinda doubting Bubba153 was a DIY'er since he has asked for help with over 12 different appliances...

Maybe he should gain access...

16345Ed Sensei

16345Ed

Posted
Posted
5 minutes ago, Chat_in_RI said:

Was kinda doubting Bubba153 was a DIY'er since he has asked for help with over 12 different appliances...

Maybe he should gain access...

I think grasshoppers haven't paid. ?

 

I agree it's the best money a professional tech can spend. 

Hiroshi Sensei

Hiroshi

Posted
Posted

On the slightly older models- "0" "0"  or "88" "88" flashing was a communication error... I'd put the original board back in and see if it goes back to normal...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing
×
×
  • Create New...