FAQs | Repair Videos | Academy | Newsletter | Contact
Search the Community
Showing results for tags 'washer'.
-
When we try to start a wash cycle it seems to get ready for the fill but then no water is dispensed. We can fill it with a hose and then it will run, seems to do the rest of the cycle normally. Any ideas? Thanks, Jerry
- 10 replies
-
Maytag Dependable Care Top Load Washer Service Manual
Samurai Appliance Repair Man posted a file in Appliance Repair Manual Pot Luck Supper
-
The current status is: Dryer works fine Washer light comes on when activated (i.e. pull the knob out) Washer does not Fill with water Rotate Drain (based on sound) I'm looking for information to help me find the pump (ic) board; check the fuse; test the pump I don't know if I have multiple failures (perhaps caused by the impact when the spring broke): the speed controller, the pump, etc. Please advise History, oldest to most recent Washer ande dryer worked fine Loud noise and washer stopped rotating in any mode Diagnosed a broken support spring Received and installed a replacement spring (and a replacement electric washer moter, belt, and schocks ready to return for a refund) Washer fills but does not spin. During what would be wash cycles, the drum rotates rarely and slowly. Drain pump makes a lot of noise Remove drain hose (drump to pump) and empty coin trap (it was full) Reinstall drain hose Washer fills but does not spin. During what would be wash cycles, the drum rotates rarely and slowly. Drain pump makes a lot of noise Attempt to clear hose from pump to exit pipe
-
110.20722990 Kenmore washer spins-and-stops endlessly, replaced several parts with no luck
jimburden posted a topic in DIY Appliance Repair Help
The problem is the washer spins and halts, spins and halts, endlessly on most dial settings, regardless whether the lid is open or the dial is pulled. The only way to stop it is to unplug the machine. (It will fill with water on the CLEAN setting.) Here's a video I took of the problem. What I've done so far, all with no effect: Replaced the timer. Replaced the motor and motor switch. Replaced the entire wire harness. Replaced the lid switch. Tested the pressure switch (all good). Tested the capacitor (all good). Double-checked that the power outlet works and no fuses are blown. I'm suspicious that it's the transmission. Reasons: I noticed there's oil leaking on the floor. It seems to be coming from the transmission. The original transmission died 6 months ago. I replaced it with a used one on eBay. Process of elimination -- I've replaced nearly everything else; what else could it be? Do you think the transmission is the culprit? Is there any other part I should check first? Thank you! -
Whirlpool Duet Washer - Selector Knob Problem - Model Ghw9150pw4
CheeseheadNV posted a topic in DIY Appliance Repair Help
The selector knob on our Whirlpool Duet washer either got misaligned or is not communicating correctly with the computer board. The knob is in good working order and I've checked that it is on the stem properly. But the cycle the knob points to is not the cycle the washer is selecting on the control panel. It's almost like it "lost" certain cycle options. When the knob points at "white wash" the control panel shows two dashed lines and no wash temp, speed, etc are selected. When pointed at the Normal Cycle, it doesn't register anything on the panel. When pointed at Delicate and Hand Washables, cycle options register on the panel but I'm not sure they are the correct cycle settings. No matter where the knob is pointed, a hot wash cannot be selected (unless I change the setting using the buttons for wash temp). Wash times and temps register when the knob points to Soak, Soak/Drain and etc. And when I turn the knob to the blank space between the drain options and the white wash, cycle times show on the control panel. We tried unplugging for 1 minutes and a reset didn't help. Any idea what could be wrong and if it is serviceable? Thanks for any tips. -
Manufacturer: Kitchenaid Type of Appliance: Dishwasher Model Number: Kdte234gwh0 Have you validated the model number at an online parts site like Repair Clinic? (yes or no): Yes Have you watched the video on how to search for manuals and have you searched the Downloads section prior to posting this request? (yes or no): Yes Manual needed thz
-
Manufacturer: Ge Type of Appliance: Washer Model Number: GTW680BSJ3WS Have you validated the model number at an online parts site like Repair Clinic? (yes or no): Yes Have you watched the video on how to search for manuals and have you searched the Downloads section prior to posting this request? (yes or no): Yes How do I change the tension rods on these? I had to abandon a job today because I couldn’t figure it out please help part number WH16X26911
-
Hello! I keep getting a water error on my Miele W1926 washer. I've cleaned all (4) of the hose filters multiple times, but I'm still intermittently getting this error. I found a thread on automaticwasher.org where folks were commenting that the triple intake valve can get clogged by hard water and the usual fix is to replace this valve. For the life of me, I cannot find a parts diagram or repair manual that lists the part number. I'm about to just tear into it and see if the valve has a part number listed on the side, but figured I could post here in case one of the experts here has any of the documents that may help me out! Thanks!
-
New Appliance Service Manual added: LG FL Washer Door Lock dE and dL Error Code Troubleshooting
Samurai Appliance Repair Man posted a topic in Appliance Service Manual Requests Forum
File Name: LG FL Washer Door Lock dE and dL Error Code Troubleshooting File Submitter: Samurai Appliance Repair Man File Submitted: 10 Jul 2013 File Category: Appliance Repair Manual Pot Luck Supper LG FL Washer Door Lock dE and dL Error Code Troubleshooting Training video Click here to download this file -
Version 1.0.0
1,695 downloads
Intermittently Spin Up, Wet Loads, Not Spinning Models affected: GTW220ACK(1 – 4)* GTW330ASK(0 – 3)* GTW490ACJ(0 – 4)* GTW680BPL0DG GTW750CPL0DG GTW750CSL0WS GTW460AMJ(0 – 4)* GTW680BSJ(0 – 5)* HTW200ASK(0 – 3)* GTW460ASJ(0 – 8)* HTW240ASK(0 – 3)* GTW485ASJ(0 – 4)* GTW685BPL0DG GTW685BSL0WS * Numbers in parentheses represent all engineering digits in that range. (Example ACK(1 - 4) represents ACK1, ACK2, ACK3 and ACK4) Serial numbers: HF – GL (May 2015 - April 2018) PUB HL04-18 -
GE Top Load Laundry Service Bulletin - Intermittently Spin Up, Wet Loads, Not Spinning View File Intermittently Spin Up, Wet Loads, Not Spinning Models affected: GTW220ACK(1 – 4)* GTW330ASK(0 – 3)* GTW490ACJ(0 – 4)* GTW680BPL0DG GTW750CPL0DG GTW750CSL0WS GTW460AMJ(0 – 4)* GTW680BSJ(0 – 5)* HTW200ASK(0 – 3)* GTW460ASJ(0 – 8)* HTW240ASK(0 – 3)* GTW485ASJ(0 – 4)* GTW685BPL0DG GTW685BSL0WS * Numbers in parentheses represent all engineering digits in that range. (Example ACK(1 - 4) represents ACK1, ACK2, ACK3 and ACK4) Serial numbers: HF – GL (May 2015 - April 2018) PUB HL04-18 Submitter Lighthouse Submitted 04/26/2018 Category Appliance Repair Manual Pot Luck Supper
-
Whirlpool Washer MVWC360AW0 Parts List & Tech Sheets
RegUS_PatOff posted a file in Appliance Repair Manual Pot Luck Supper
-
NEED HELP WITH GROUND WIRE LOCATIONS - MAYTAG MODEL MAV551EEWW TOP LOAD WASHER
AdrianBailey34 posted a topic in DIY Appliance Repair Help
MAYTAG TOP LOAD WASHER - MODEL MAV551EEWW I’ve got a Maytag Top Load Washer - Model No. MAV551EEWW - and I’ve recently had to replace the Drain Pump when it became noisey. Before concluding that I needed a new Drain Pump, I had taken the washer almost completely apart (removed wiring connections from control board, removed ground wire screws, removed drive motor, removed drive belt, and finally removed drain hoses/pump) - after receiving the new Drain Pump and installing it, I’ve got everything all but put back together....The ONLY thing I’ve now run into is I cannot remember where all the ground wires either screw/mount onto the frame!! Help!!! There are a total of either four or five ground wire connections - two are located by the drive motor; one connects to the frame of the washer cabinet, the he other connects to the mounting plate for the motor - then the other two or three grounds are up top by the control panel/power cord wiring/front panel/lid switch. Please help me figure it out - I know it’s a grounding issue because I’ve tripped our breaker three times for the outlets/lights in our laundry room upon trying to plug the washer in to test the new pump! -
Kenmore Washing Machine VMW Model 2130 (P/N W10420384A) not spinning and draining every time
metallicviper posted a topic in DIY Appliance Repair Help
Error Codes after using Diagnostic Setting: F9E1 - drain pump system problem - long drain F0E2 - Over Suds Detected This issue has been on/off over the last few weeks – and we were able to deal with it until now. Basically what happens, is the load starts washing and then it just stops when it gets to “spin”. Sometimes it just shows the red “lid lock” light only. When I cancel it and look inside, either the clothes are pretty wet but no sitting water (i.e. it drained but didn’t spin) or there’s a ton of water still there (didn’t drain or spin). We’ve been able to cancel the cycle – manually move it to the “drain and spin” setting and it would normally work at that point to finish off the load. We use high efficiency detergent and I took the drain apart and looked for anything blocking it – found nothing. The drum does freely turn so it can spin as it does occasionally work as well. All that said, now it makes a weird buzzing sound when you try to choose anything with the dial (attached recording). Please help! TL;DR – Washer begins the wash – then doesn’t spin or drain. Error codes F9E1 and F0E2 -
New Appliance Service Manual added: LG WM3900H*A Washer Service Manual and Bulletins
Cowboy Mike posted a topic in Appliance Service Manual Requests Forum
LG WM3900H*A Washer Service Manual and Bulletins View File Service Manual and related bulletins for WM3900HBA.ABLEUUS Service manual PUB MFL68588942 WIFI connection fail through ThinQ aplication Bulletin PUB DFZ201900148-01 When replacing the detergent box for water remaining in the dispenser Bulletin PUB DFZ201900119-01 Guide to IE Errors Caused by the Siphon Effect Bulletin PUB DFZ201900167-04 Applying Tape to PCB Covers when they come off Bulletin PUB DFZ202000123-0 Submitter Cowboy Mike Submitted 10/01/2020 Category Appliance Repair Manual Pot Luck Supper-
- front loader
- washer
-
(and 1 more)
Tagged with:
-
LG WM3900H*A Washer Service Manual and Bulletins
Cowboy Mike posted a file in Appliance Repair Manual Pot Luck Supper
Version 1.0.0
407 downloads
Service Manual and related bulletins for WM3900HBA.ABLEUUS Service manual PUB MFL68588942 WIFI connection fail through ThinQ aplication Bulletin PUB DFZ201900148-01 When replacing the detergent box for water remaining in the dispenser Bulletin PUB DFZ201900119-01 Guide to IE Errors Caused by the Siphon Effect Bulletin PUB DFZ201900167-04 Applying Tape to PCB Covers when they come off Bulletin PUB DFZ202000123-0 -
Manufacturer: Electrolux Type of Appliance: Washer Model Number: Eifls60jiw1 Have you validated the model number at an online parts site like Repair Clinic? (yes or no): Yes Have you watched the video on how to search for manuals and have you searched the Downloads section prior to posting this request? (yes or no): Yes Drum spinning and banging Service manual needed thanks
-
Manufacturer: Maytag Type of Appliance: Washer Model Number: Mvwc5esxw0 Have you validated the model number at an online parts site like Repair Clinic? (yes or no): Yes Have you watched the video on how to search for manuals and have you searched the Downloads section prior to posting this request? (yes or no): Yes Service manual needed
-
SAMSUNG WASHER WF501ANWXAA 01 - ERROR CODE 8E2
AppleFritter posted a topic in DIY Appliance Repair Help
I've searched all over the google and this forum and can't seem to find info on this.. I keep getting an 8E2 Error code on my machine and can't seem to find a good consensus on what it actually means. SAMSUNG WASHER WF501ANWXAA 01 - ERROR CODE 8E2 - Basically the washer will stop and beep but then eventually start back up. The start up time is sometimes just a few seconds to longer. I go give it a whack on the top and sometimes it starts it up but that could just be coincidence? Anyway, TIA -
Manufacturer: Kenmore Type of Appliance: Washer Model Number: 587.14402400 Have you validated the model number at an online parts site like Repair Clinic? (yes or no): Yes Have you watched the video on how to search for manuals and have you searched the Downloads section prior to posting this request? (yes or no): Yes Service manual needed
-
Manufacturer: Kenmore Type of Appliance: Washer Model Number: 417.40412701 Have you validated the model number at an online parts site like Repair Clinic? (yes or no): Yes Have you watched the video on how to search for manuals and have you searched the Downloads section prior to posting this request? (yes or no): Yes Need service manual for disassembly need tech sheet as well thx
-
Manufacturer: Kenmore Type of Appliance: Washer Model Number: 796.41072310 Have you validated the model number at an online parts site like Repair Clinic? (yes or no): Yes Have you watched the video on how to search for manuals and have you searched the Downloads section prior to posting this request? (yes or no): Yes Service manual and tech sheet needed thx
-
Manufacturer: Maytag Type of Appliance: Washer Model Number: Mvwb980bw0 Have you validated the model number at an online parts site like Repair Clinic? (yes or no): Yes Have you watched the video on how to search for manuals and have you searched the Downloads section prior to posting this request? (yes or no): Yes Service manual needed
-
Wt1101cw need Service manual and tech sheet
Osayi posted a topic in Appliance Service Manual Requests Forum
Manufacturer: Lg Type of Appliance: Washer Model Number: Wt1101cw Have you validated the model number at an online parts site like Repair Clinic? (yes or no): Yes Have you watched the video on how to search for manuals and have you searched the Downloads section prior to posting this request? (yes or no): Yes Need tech sheet/ schematic need service manual for disassembly -
Manufacturer: Lg Type of Appliance: Washer Model Number: Wt4970cw Have you validated the model number at an online parts site like Repair Clinic? (yes or no): Yes Have you watched the video on how to search for manuals and have you searched the Downloads section prior to posting this request? (yes or no): Yes Service manual and tech sheet needed