Search the Community

GE Monogram ZISS420nmcs, side by side cabinet depth unit. condenser is in the "ceiling" of the freezer compartment. Water is leaking, and freezing, from the ceiling of the freezer. Started making a terrible noise (fan was hitting the ice). I have removed all screws but cannot seem to remove the ceiling panel. There is a small opening, I can reach in and feel ice above the ceiling. I suppose I can fix the symptom by letting all of the ice melt and simply turning off the water to the ice maker. Any better suggestions? TIA !!

LG Refrigerator Service Bulletin - Water overflowing or splashing from fill tube View File Water overflowing or splashing from fill tube Water leakage from ice maker, Ice build up in the chute. Fill tube angle wrong. Country Model (ECN) Serial Number Range USA/ Canada LFXS32726S (00,01) ~607KR* USA/ Canada LFXS32766S (00.01) ~607KR* USA/ Canada LFXS30726S (00.01.02) ~607KR* USA/ Canada LFXS30766S (00,01,02) ~607KR* USA/ Canada LFXS30766D (00) ~607KR* USA/ Canada LFXS29626W (00,01) ~607KR* Country Model (ECN) Serial Number Range USA/ Canada LFXS29626S (00,01) ~607KR* USA/ Canada LFXS29626B (00,01) ~607KR* USA/ Canada LFXS29766S (00,01) ~607KR* USA/ Canada LFXC24726S (00,01,02) ~607KR* USA/ Canada LFXC24726D (00) ~607KR* USA/ Canada LFXC24766S (00,01,02) ~607KR* PUB CNZ201600426 Submitter Chat_in_FL Submitted 10/17/2017 Category Appliance Repair Manual Pot Luck Supper  

How do I insert an image? I’m using an iPad. Thanks.

Amana Model # ASD2522WRS01 Ice Maker leaking into bucket Makes and dispenses ice--cubed and crushed--just fine Leaks less but some when turned off by lifting internal "full" shutoff arm Leaks more when turned on (almost enough to freeze around the spinning cube "feed" rotor down the center bottom of the bucket) Water dispenser quit working over a year ago; replaced filter and it worked intermittently, then quit again; don't care about that but mentioning in case it's related; freezer made ice well without leak for at least a year since water dispenser quit Troubleshooting so far: Water pressure good; condenser coils clean Tested Water Valves lower back of unit: Green Valve: 250 ohms Red Valve: 200 ohms (not digital so approx.) Raised freezer setting slowly after a good thaw and clean (was sub-zero) to where it fluctuates between approx. 0 and +10 F. That was 2 weeks ago. Icemaker may be leaking at its own shutoff valve (inside black housing below the timer wheel--just behind the labelled cover) Don't mind paying $80+ for a new unit but don't want to waste that if it's the valves or something else. Can someone confirm: Next step swapping out the ice maker unit with a new one?

LG Dishwasher Service Bulletin - El E1 AE RE Error - Overfill or Leak - Filter Sump Model View File Dishwasher: El / E1 /AE / RE Error: Overfill or Leak: Filter Sump Model PUB 9098 Submitter Chat_in_FL Submitted 11/28/2017 Category Appliance Repair Manual Pot Luck Supper  

Hi all, just week I've had two occurrences where the pan of my trusty D1706 Asko dishwasher has been full (and overflowed). After drying it all out and looking for leaks during all cycles and drains I am stumped. Attached to the inside top edge of the steel access panel there's a line of spongy foam padding (looks like carpet pad) which was saturated. There's also a plastic "drip sheild" (part #8058486) that I presume is to catch drips from above. I don't think the door was open or full of water any more than normal use, but this wet foam is my only clue. Does this point to any solution for any of you veteran Samurai? Thanks, Steve

Bosch SHE3ARF2UC/07 Dishwasher Thanks for reading. Any help would be appreciated. Water has been running out from under the machine during and after cycles. Removed the bottom access panel and observed a few express wash cycles. No drips observed, but water would collect under the front feet, puddle there and then run out from under unit. Also observed water in the brackets where the door springs ride. Disconnected and pulled the unit out to inspect. The bottom of the insulation blanket is wet around the exterior of the unit and there is water laying in the gap where the plastic bottom tub and the stainless housing meet--almost all the way around. There is no obvious signs of leaking around the water inlet/vent assembly. Fittings on the drain line, vent and supply appear dry. I was hoping this was just a door gasket, but now I'm thinking it may be even worse than I first thought. Any insight would be appreciated. Thank you so much.

Hello—I'm back with a new issue. This time it's with my Kenmore Elite HE5t Washer (model 110.47789701). Recently it has been leaking water from the lower half of the right panel during the spin cycle. We have noticed that the water leaks more if we do multiple washing loads in a row. (I mop up the water after each time.) I would guess the total amount of leaked water is about a 1/2 cup per load. Any thoughts on what might be causing this? PS—For those who assisted with the dryer, the repairman came back a third time. We inspected the dryer's blower housing, and it was clean. After inspecting all of the heating element's fuses with no success in pinpointing the problem, he guessed it was a faulty circuit board. Rather than spending more money on a circuit board or hiring a newer repairman, we cut our losses and bought a new dryer.

GE Dishwasher Service Bulletin - Condensation or Fogging on Floor or Toe Kick Panel View File Models affected: CDT765S, PDT750S, PDT760S, ZDT800S and ZDT870S PUB DD01-16 Submitter Chat_in_RI Submitted 04/30/2016 Category Appliance Repair Manual Pot Luck Supper

During any cycle that uses water, the machine is leaking water out the rear plastic cover that covers the electrical gear and valves. I removed the cover and the entire inside (valves, etc) are soaked. Floor has a large puddle. Google found me nothing - can't find any indication of where the water is coming from, other than the valves or perhaps the cups that store the detergent/softener. Any ideas?

File Name: GE Top Control Dishwasher Service Bulletin - Water on the Floor File Submitter: Chat_in_FL File Submitted: 19 Dec 2015 File Category: Appliance Repair Manual Pot Luck Supper Supersedes DD04-13 Models: GDWT608VWW PDWT302VII ZBD6900VII GDWT608VBB PDWT380VSS ZBD6920VSS GDWT668VSS CDWT980VSS ZBD7920VSS GDWT708VWW PDWT480VSS ZBD8900VII GDWT708VBB PDWT500VWW ZBD8920VSS GDWT768VSS PDWT500VBB PDWT200VWW PDWT502VII PDWT200VBB PDWT580VSS PDWT280VSS PDWT505VWW CDWT280VSS PDWT505VBB PDWT300VWW PDWT585VSS PDWT300VBB PUB DD12-14 Click here to download this file

I have a slow drip from my Rudd Water Heater through the Temp and Pressure Relief Value. The heater is a Power Vent model PVP75FW We are on well water and the water contains minerals which have damaged other appliances. We have installed a CSI filter recently. So, being a relief valve, I'm wondering if it is "Relieving" itself or if I may have a damaged valve. And just out of curiosity, how many others type "value" for "valve". I seem to do it all the time. dgp By "slow leak" I mean perhaps just under a gallon over 30 hours or so.

I found a post in this forum that appears to answer my question, but I wanted to start a new topic to get a better grasp of the big picture. My p&t valve line goes up and out to the patio. There appears to be water there (maybe 8 to 10 oz) every morning (after showers?). Here's the post that leads me to believe its either build up or too much pressure. http://appliantology.org/topic/27317-water-heater/?hl=p So if it is too much pressure, here's my question; how much pressure should be coming in from the street? Its City water. Is this a measurable thing, for a non-plumber like myself? A way to test it? We have a toilet that chronically runs for a second or two occasionally (I've replaced the entire tank kit by now) that also made me think I had too much pressure. I'm familiar with the valve to limit the incoming pressure, but only in passing. I say hello. Its silent... Any advice would be grratly appreciated. Even if its "Dude, call a plumber..." I can post pics and models #'s, but for now its more of a general, philosophical discussion. Thanks, D